Search found 43 matches
- Tue Aug 14, 2018 9:31 am
- Forum: FAQ about Tulipp Development Platform
- Topic: SDSoC 2017.4 issues creating platform
- Replies: 6
- Views: 59767
SDSoC 2017.4 issues creating platform
> Dear Timoteo, > > I am writing to see if you have successfully created an SDSoC platform for the HDMI board on SDSoC 2017.4. So far, I managed to create a simple one without any issues. Now, I took Sundace's hdmi input/output from hackaday for the zynq, which is on 2017.2 and adapted it to 2017.4...
- Fri Apr 27, 2018 12:17 pm
- Forum: FAQ about Tulipp Development Platform
- Topic: PIN selection for Ultrascale +
- Replies: 1
- Views: 4933
Re: PIN selection for Ultrascale +
You can use this:
(I assume the one you need is TE0820)
(I assume the one you need is TE0820)
- Wed Apr 04, 2018 11:07 am
- Forum: FAQ about Tulipp Development Platform
- Topic: Regarding the hardware manager
- Replies: 13
- Views: 86517
Re: Regarding the hardware manager
Thanks Flemming for that detail I missed! Regarding the voltage setup: You can select 3.3V, 2.5V and 1.8V, because that module installed on the carrier board (the little board with the heat sink) is not the only module available to put there. There are other modules with different IO voltages that c...
- Tue Apr 03, 2018 4:18 pm
- Forum: FAQ about Tulipp Development Platform
- Topic: Regarding the hardware manager
- Replies: 13
- Views: 86517
Re: Regarding the hardware manager
Hi Timoteo, Thank you for the reply. A quick note I have installed vivado 2017.1 on ubuntu 16.04 The power supply cord used, is from my lab because we do not have the power supply cord provided by you. And no, it is not the Xilinx USB platform as shown in the picture. We have got an OLIMEX ARM-USB-...
- Tue Apr 03, 2018 10:33 am
- Forum: FAQ about Tulipp Development Platform
- Topic: Regarding the hardware manager
- Replies: 13
- Views: 86517
Re: Regarding the hardware manager
Hi Pranjali, The reason why you wouldnt see the device in the JTAG chain could be: -The board is not being supplied properly (to check this, measure the 3.3V levels). Before you do anything, quick question: Is the power supply you are using yours, or provided by us? -The USB platform is not working ...
- Mon Oct 02, 2017 2:40 pm
- Forum: FAQ about Tulipp Development Platform
- Topic: Over voltage protection of TTL GPIO ports
- Replies: 5
- Views: 11126
Re: Over voltage protection of TTL GPIO ports
Hi Timoteo, I unplugged the SD card and turned the EMC2DP on. This I assume does not program the FPGA and run software on the Zynq. I see the same behavior. TTL1 and TTL3 are at 1.8V. TTLVCC is at 1.8V. Other TTL pins pins i.e., TTL0, TTL2, TTLN, TTLP, and TTLGND are at 0V. - Ananya Hi Ananya. Do y...
- Fri Sep 29, 2017 11:46 am
- Forum: FAQ about Tulipp Development Platform
- Topic: Over voltage protection of TTL GPIO ports
- Replies: 5
- Views: 11126
Re: Over voltage protection of TTL GPIO ports
Hi Ananya, If you power up the board, without programming the FPGA or make the Zynq boot (basically having the TTL pins unconnected from the FPGA's point of view), and you measure the voltage on every pin of JP3, what do you see? It should be all 0, except VCCIO34 (1.8V). In case you are seeing 1.8V...
- Tue Jul 18, 2017 10:55 am
- Forum: FAQ about Tulipp Development Platform
- Topic: Direct connection between accelerated function
- Replies: 4
- Views: 12150
Re: Direct connection between accelerated function
Hi, That's a good question. I'm not a C developer (for now!), but I understand by concept that you should optimize your code in order to get the maximum performance in your application with SDSoC. About your question, remember that SDSoC is based on HLS, and the way your functions in C are translate...
- Thu Jul 13, 2017 5:06 pm
- Forum: FAQ about Tulipp Development Platform
- Topic: Will the upcoming ultra scale version of the tulipp board support the camera link interface?
- Replies: 1
- Views: 5149
Re: Will the upcoming ultra scale version of the tulipp board support the camera link interface?
The current version of the tulipp board (zynq 7030) does not support the dual camera link interface due to the lack of high-range banks. Will the ultra scale version of the tulipp board have this banks available, so that the camera link interface ist supported? regards Matthias Hi Matthias, The Ult...
- Fri Jul 07, 2017 12:02 pm
- Forum: FAQ about Tulipp Development Platform
- Topic: Pitch of EMC2 LVTTL IO port connector
- Replies: 3
- Views: 8578
Re: Pitch of EMC2 LVTTL IO port connector
Hi Ananya,
Same measures than JTAG.
Page 9 you can see the exact numbers
https://www.xilinx.com/support/documentation/data_sheets/ds300.pdf
Timoteo
Same measures than JTAG.
Page 9 you can see the exact numbers
https://www.xilinx.com/support/documentation/data_sheets/ds300.pdf
Timoteo